Remaining SAO notes

On May 25, 2014, in Sword Art Online, by Toast

This is a long purely test post with some remaining rambling about Kirito builds.  Try not to fall asleep.

 

The shoulder strap and chest piece:

AKA how the swords free hung from my back. This was my biggest pet peeve with most of the Kirito cosplay I had seen. Either there was no sword sheaths or they were connected to belts which had nothing to do with the chest strap (and were inaccurate). I also saw a few which had connected it to the chest strap but the chest strap had come out to be thick belts and/or armour instead of just another fabric piece like it is on the character.

As a result I set out to find a solution to all of these pet peeves. If I hadn’t succeeded I likely won’t have even cared to wear this cosplay.

Thankfully, all my work wasn’t wasted. But enough yammering.

Chest piece creation:

The base of the chest strap was a loop attached to a loose piece of strap, which buckled into the rest allowing for easy removal of the piece.

This base was covered in the same fabric that I made my Kirito jacket out of, and the same (self-made) bias tape was used to cover the edges. This was made to fit very tightly to my body over the jacket. It had three purposes;

–          Look damn sexy

–          Hold the jacket in the correct (open) position

–          Hold the swords and their sheathes

I have a wonderful photo of myself in the bathroom modeling just this piece on my facebook page.

The chest armour was constructed from foam and worbla and pressed to my chest so that it molded right onto my body. This really is the wonderful part of thermoplastics, everything can mold right to you. The piece had two levels, inside the worbla I put two pieces of foam together to create the lower surrounding edge on the piece. The circles were thin strips of worbla wrapped around a cup, then were squished onto the main piece. This was gessoed, sanded, rub n’ buffed, buffed and covered in future. It was then applied to the chest strap to hide the buckle.

 

Attaching the swords:

In retrospect, this should have been done earlier. Since you are reading this, if you plan to follow my methodology for this, please don’t make my mistakes. Hindsight is 20/20 on this one, but my design worked out in the end.

My mistake is simple, my sheathes were completed when I decided to go about this task. Big no-no, this should have been a part of the design process. Aside from that, all is well aside from using contact cement instead of super glue to attach some Velcro, which is a fixable error. Side note: It has now been re-attached with super glue and is 100% solid.

I added Velcro to each case to get them to stick together in the correct position on my back. This made them into a single object to deal with hanging, though they would still come apart so they were easier to store and it was still possible to cosplay pre-dual wield Kirito if I so pleased. Before doing this check, re-check, re-re check, re-re-r… you get the point, your references to make sure you have the correct case set up and the correct case on top. Once you’ve done that, apply Velcro to their cross over area on the correct faces.

With the cases connected I held my chest strap piece up to them and sketched out where the chest piece would hit them, one case would slide on, the other would have a Velcro strap that could be done up and un-done around the chest strap. The Elucidator has the Velcro strap and the Dark Repulser has the slip on ring.

The slip on ring was made from the same backpack material. I cut two holes in my foamboard case and slid the piece through. As I like to worry I applied two layers of worbla to this area and some of the surrounding area on the case to make sure this area wouldn’t tear. Even though my foamboard sword was a massive 0.8lbs, I wasn’t willing to take any failure chances.

Why this isn’t ideal: The strap rubs against the sword since it is inside the case, possibly ruining the paint. You’ve also had to make a later modification and have possibly weakened the sheath.

How to be better than me: Attach the strap to the case in a different manner (worbla added on the external part of the case as part of the build that holds the strap for example). If you must snake it inside, cover it in felt or fleece and make sure it is flush or close to flush with the rest of the case,.

The Velcro ring was two pieces of Velcro sew together. Like the strap it snaked through the case. I placed the “soft” side of the Velcro inside the case but I still panicked every time I had to pull the elucidator out of the case fearing damage to the paint job. I don’t need to detail why this isn’t ideal, it’s obvious. Thankfully unlike the foamboard the worbla case doesn’t have a big concern about a loss of strength or stability from such a small cut. However just to be sure I applied an extra layer of worbla to this area.

How to be better than me: Same as above, pre-plan, make it flush. If you are using Worbla you may chose to place it with-in the initial “sealing”, allowing it to stick out. Sew the two pieces together and place the inside the piece with the foam, having small slits for them to exit the piece. This would make the fixing very strong and permanent inside the piece, however I would suggest double layering the worbla in this area on the outside just to be sure everything will hold.

This system was easy to take on and off, was accurate and was very comfortable. I wasn’t in pain after wandering around with the sword for 8 hours at the convention, considering my Haseo cosplay it was something I was more than thankful for.

Other notes:

I don’t feel the need to detail my shoe and arm armour. They were done with worbla just like the chest armour, the little bump details were done with screws which I had cut the bases off of. These details are likely suppose to be rivets, but I liked how the screws looked. The arm armour stuck on with Velcro, the shoe armour just used elastics as the boots I wore are boots I rather like for real life things (when armoured shoes might not go over so well).

The jacket was sewn by me, the wig was styled by me and the bias tape used was handmade as I didn’t find any with the colour I liked. The was my most comfortable cosplay to date. It was fun to take pictures with people in it as I could give them a sword to hold (or to threaten me with).

I have two future projects that I aim to finish this year, some Tera online armour http://tera-online.cc/uploads/gallery/main/55/castanic_m_h27.jpg and Toan from Dark Cloud (giant glowing sword FTW). Will try to post notes/ect on these as I go. May eventually put up a post about how my Shadowy Death was built.

Tagged with: