Haseo, Part 5

On October 13, 2012, in .Hack//G.U. / Haseo, by Toast

Last post for Haseo, at least until I decide to build a few more pieces for the costume.  I have started on another project and will post some updates on that in little while.  In the mean time I may discuss some tools or materials.

I still have to build the weapons (the guns) or another of his weapons (Twin blades, scythe or chainsaw sword).  Although I have built the twin blades in the past for my Haseo first form cosplay, and did still own them when I wore this cosplay, they were some of my learning props and didn’t fit with the rest of the Xth form cosplay’s quality/look.  I may consider the scythe just to try out a different scythe building technique (I’m interested in trying expanding foam out for a prop and having a staff the breaks into pieces), but that won’t be for a little while!  I don’t have a workshop or workshop space in my current home so many large projects will have to wait.

For anyone interested.  This  was my Haseo first form cosplay.  I’ve learned a lot about cosplay since I did this, changed many methods I use (and gotten the cash to pay for some better tools and materials).

Knee armour:

This was some of the more challenging armour to think through making.  The basic shape of it is a cylinder which slowly expands outwards, then with a second cylinder attached below.  At this point in my process I was also running out of wonderflex (and time) so I made do with friendly plastic for a few parts.

I, sadly, have no progress pictures for this piece so I can only really discuss the theory of how they were built.

The base was created out of a few pieces of foam, covered in wonderflex and placed around a pot to assure that they would be round.  The edges that stick out are foam covered in friendly plastic.  The bottom part was done in the same manner and attached to the top portion.

Wiring was very simple for this piece as there was only two LEDs.

These stayed on using an elastic which went just under my knee (over the muscle right there) and attached onto velcro on the front of my black tights.

Collar:

Originally I believed that this would be the single least comfortable piece of the armour, it was sadly beaten by the sunflower.  Although the theory of this piece was good it felt like it just stood on my body and didn’t really fit as well as it should have.  I may rebuild this at some point.  To anyone else building this piece I would suggest attempting to shape it to your neck area a bit better.

The base of the collar was foam, to create the soft appearance of the piping instead of adding wonderflex on top of the base I stacked the foam, then wonderflexed it.  I did like this effect for this piece in the end and felt it was effective.

The two pictures below show the wonderflexed and shaped foam (and my lovely socks).

From here I did the normal wonderflex prep (gesso, lots of sanding).  The painted the item.

I blended the rub’n’buff with a bit of satin gloss to thin it out so I could treat it as paint, this worked really well and didn’t change the colour or effect of the rub’n’buff.

And the final item:

My painting is still a bit shaky, I am looking to improve this in the future :)

Shirt armour:

This was built in the same way the belt armour was; foam, mod podge, paint and wiring.  There is some wire in the piece that I used to keep it stiff and shaped, it helped it sit better.

As this was my first time using just foam for armour (no wonderflex, no styrene) I was very happy with the result.  It took paint well and came out smooth.  These two pieces have opened by eyes to foam armour a bit more, I may end up using it in a few more project going forward.

The wiring ran along the entire piece and the battery clipped into the opposite side of the thigh armour from the belt armour.

This wasn’t attached to this shirt direction to make washing the shirt easier (washing cosplay clothing is wise, this shirt did not smell great!).

Shirt:

The shirt, this was my sewing pride and joy of this costume.

I am not really a sewer, I tend not to sew with patterns and I’m not particularly confident in my sewing skills.  I managed through making the pants for this costume but the shirt was a different story, at least at first.

The shirt started as a near dress.  The base of the shirt came off of one of my fitted T-shirts then was significantly lengthened, originally it was to just above my knees, rather silly looking.

The front was cut in half to allow for the centre zipped, as I wanted the neck to come in very tight I wouldn’t be able to pull it on/off.  It also made it so I could walk to the convention in a different shirt, I take transit to my local conventions so I try to wear as little of my costume while transporting as possible.

Once the zipped was installed and the base shirt was somewhat fitted I had to create the lines down the shirt.  I spent a lot of time milling over different versions I had seen of this cosplay, most had simply chosen to draw on the lines.  I didn’t like this effect it tended to look too bold against the shirt and the lines of the character’s shirt look more like texture than drawn on lines.

I resolved to sewing them in.

After measuring the total I determined that the space between each line needed to be 4cm.  For each line  I pinched a bit of fabric, pinned it, ironed it (ironing was very key to keep these lines from puckering), stitched it then ironed it while it was folded, then while it was flat.  There was no puckering in the lines as a result of all the ironing.  These lines were put in all around the shirt.

Once the lines were done I cut out the black fabric.  Black fabric #1, the base, is shiny, black fabric #2 is dull black bias tape.  I liked the effect of the lining this created (and it was accurate to Haseo’s shirt, hooray!).  The bias tape was also used to line the arm holes.

The shoulder pieces were foam covered in fabric and glue.  The glue created an interesting effect on the fabric, which I rather liked.  They don’t show in any of the photos I have, but there are lines stitched into these with my sewing machine at 1cm intervals.  These are stitched onto the shirt, with some velcro to allow the collar to slide under certain parts.

The velcro on the bottom of the shirt is to hold the shirt armour, described above.  Around the neck there is velcro to hold on a leather collar that snaps around the back.  There are a few pieces of velcro to hold the collar in the correct position as well.

These photos are just of the shirt on the floor, not super attractive, but it shows all the sewing/velcro well.

Upper arm armour:

I hated this piece, with a passion as well.  In fact I dislike this piece so much I don’t even have direct picture of it to provide!  It broke both days I wore the cosplay, was very uncomfortable and further restricted my movement (which the other parts of the cosplay had done plenty already!).  I will be re-doing this piece with craft/eva foam in the future.

How this was built (again, I do not suggest following this!):

Wire was formed for each piece, glued together with a dab of hot glue.  A 1 cm piece of craft foam was slit in the middle and one was added to each side of the wire.  At this point the piece would fit my arm, but wasn’t tight.  These were covered in a thin layer of air dry clay.  These pieces were connected using a thin piece of balsa wood (likely my biggest error) then the shape on the connector was built up on top of the balsa wood.

These were then painted and finished.

Again, I do not suggest this method.  I think I will aim for shaped thick foam next time, connected by foam.  This would give a bit more flexibility and would not break as easily!

And that’s it for Haseo!

Here are a few more photos of the costume, but we’re done with this guy for now.

This was my largest, longest and most challenging project to date.  My next one is a bit easier but I certainly look forward to attempting another one like this!

Will post about my new project/some other tutorials in a bit :)

Tagged with:
 

Haseo, Part 4

On September 20, 2012, in .Hack//G.U. / Haseo, by Toast

Anther multi-part post!  Trying to finish up the Haseo posts so I can get to slowly posting newer things :)

The wig:

I have always been a little afraid of wigs, my wig for my first form Haseo cosplay did not go over well.  I didn’t like the pure white colour of it, it was too thin and it wasn’t long enough to do all the spikes.  On top of all that, the back part didn’t even stay up correctly.  However it had been a few years since that wig and I’ve learned a fair amount since then.  I picked a non-white colour this time as I find it a bit more flattering and the Xth form has slightly darker hair than the other Haseo forms anyhow!

I do not have any progress photos of this, just some (after the con) completed photos.

I used a Magnum from Arda Wigs in Light grey (107) then some extra sort wefts in the same colour.

I have to say this is the nicest short wig I have ever purchased, I had heard good things about Arda and they certainly lived up to everything I had read.

Extra wefts were added to the side of the wig right at the ears to allow slightly longer side spikes and to allow a bit more detail in those spikes.

For spiking I used got2b glued and got2b freezing spray.  This was where I had made my mistake last time.  Most gels and hair sprays do not work on wigs due to the lack of hair oils however these two products work extremely well on wigs.

After clipping the front hair away from the back I built up the large back spike, thinning a lot of hair away as I went.  The magnum is an amazingly thick wig, I would estimate I removed 1/4th of the fiber that was on the wig.  Once the back was built up I slowly worked on spikes, using thinning scissors and a hair razor (both purchased at daiso) to cut them.

And here are the end results:

Wave Tattoos:

(Can be seen in the wig photos on Haseo’s face/upper arm)

The wave tattoos on the cosplay were done with Alcohol Activated Makeup, Dura in 302 red.  This stuff was wonderful.  Once it was drawn on well it looked great all day – I had a few cosplayers ask how my make up wasn’t smudging.  This stuff is easily found online through many makeup retailers and cosplaysupplies.com.  I purchased mine in person at Studio FX in Vancouver, great place for cosplay makeup for those of us in the lower mainland.

The only down side to it is taking it off involves rubbing a lot of 99% alcohol on wherever you had the makeup, in my case my cheeks, and that can dry out your skin or make it very angry.

I can’t recommend this stuff enough for doing tattoos/marks in cosplays!

Back Piece aka “The Sunflower”

This piece got it’s nick name of the Sunflower from my significant other and it stuck, it really suits the piece and I will refer to it as such from here on.

The sunflower was the least comfortable piece of the costume, it forced me to stand in a certain position and disabled my ability to lean against walls for a quick break. It also prevented my arms from sitting against my sides, combined with the upper arm armour (which I will be re-designing, I was unhappy with it in the end) I ended up having to walk in a very funny fashion.

To start this piece was based around a thin PVC pipe which was cut and bent to shape.  It broke at the middle to allow me to easily take it on and off, it was held together by a doweling inside the pipes and a velcro strap on the outside.  This pipe was covered in foam pipe covers (the black ones), this was covered in wonderflex to give it a stronger base then that was covered in light-weight air dry clay to smooth it out.  Although it seems like a lot of layers, there was little weight to this piece and there were no issues with it breaking.

The spikes were created with floral foam as a base then covered in wonderflex.  To hold them in a hole was cut into the pipe cover to fit each spike, then each spike had a balsa wood doweling that inserted into a hole in the PVC pipe it self.  I had no issues with these either, they lived through many bumps by many people (always try to look out for people, especially cosplayers, at conventions!).

And the final sunflower (bottom part not shown);

Thanks for reading :)

Tagged with:
 

Haseo, Part 3

On September 13, 2012, in .Hack//G.U. / Haseo, by Toast

All of the previous pieces had much better build process/detail photos than all the remainders.  For the most part I was either rushing these parts as the convention was racing up in me or they were done earlier in the process when I wasn’t taking as many photos.

Next up, shoes!

Reference photo, this time from the .Hack//Trilogy movie.

These cannibalized a pair of boots that I didn’t like all that much, they were clipped down to fit the height of the shoe.  I added a bit of pleather to the top to hide the edges caused by cutting the boot down, however most of this is hidden by the shoe armour.

The front is very similar to the bracers (Part 2), shape and piping wise.  I do not suggest using pen marks on wonderflex, the gesso didn’t cover it for many layers.  The back is a simple loop with little arms that extend down, edging went down on the back part after this photo was taken.

Gessoed + painted. Acrylic paint for the back part, then rub n’ buff for the front again.  These are not glued to the shoes, they clip on with a series of elastics and velcro.

Completed shoe armour, glowing gem and all.

A quick picture showing where each battery pack (9V) was hidden.  each shoe had its own.  The gems certainly look funny from this angle when not lit up.

Shoes: Done! :)

Additional piece: Belt

Reference photo.  The design was edited a bit to compensate for the size of my gems.

Photos of this piece are after the con, so they do display the wear created during the convention.

Due to the placement of this piece (and the fact that I was out of wonderflex by this point) this was built out of foam.  The foam was covered in three layers of mod podge to seal it then painted in the same fashion as the other pieces.

Front and back respectively.

The bends in the ‘legs’ are from the convention, not too bad for a piece in such an area.

The circuit for this clipped into one of the battery packs hidden in the thigh pieces (Part 1).  It velcroed on to the belt to keep it flat against my body and strapped around it with some elastic and velcro.  Simple enough design.

All done :)

Tagged with:
 

Haseo, Part 2

On August 31, 2012, in .Hack//G.U. / Haseo, by Toast

Next up, bracers!

These were the first piece I worked on, my first time ever using wonderflex to build anything.  I didn’t include the red floating circle due to a time restriction.

Again, a quick reference photo.

Starting with the base of the piece.  The middle is foam fit to just slide over my hand with two layers of wonderflex on the outside.  As the shape was odd I used Model Magic to build up the base shape of it.  Although super light weight model magic doesn’t hold up well on its own and will crack when drying since it shrinks, it is also not sandable.

The model magic was covered in wood glue to help harden it up and cover some of the cracks, then covered in friendly plastic (a gum-like thermoplastic).

Top of the bracer, foam base.  This was wonderflexed and all piping/details were done in wonderflex as well.

The bracer was then bent into its circle shape, the top pieces given slight curves.

Gesso and white acrylic paint done as paint prep, sanded then painted with more white acrylic paint.  Silver is done with rub n’ buff in silver leaf.

Done! :)

Haseo, Part 1

On August 28, 2012, in .Hack//G.U. / Haseo, by Toast

Worn to Anime Revolution 2012, Haseo Xth Form

There was far too much work on this cosplay to written up into one post so I’ll be posting a few pieces as at time.  First, the cuisses (thigh armour).

Quick reference of the piece, I mostly used references from the .Hack//G.U. Trilogy movie.

Base piece patterns on wonderflex.  A side note this is the size of a “Jumbo” or full sheet of wonderflex.

All pieces cut then wonderflexed.  One piece of foam to two pieces of wonderflex, double wonderflex containing a foam core to make the pieces solid.

Top of the piece coming together, bottom was built in a similar fashion,

Completed pieces, aside from the centre piece.  The stick out edges are a separate piece, attached to the main pieces same for the end tabs.  All piping is done with small bits of wonderflex.   Holes are to accommodate wiring.

Painting.    Yellow is delicate  painter’s tape, almost looked like I had switched to making iron man armour in the first picture.

Silver colour was an error and was later corrected to white.

Wiring and fixing.  Wiring goes through the piece to connect the bottom gem to the rest of the circuit.  There are two nine volts on each thigh piece, one for either a belt piece or shirt piece and one for the lights on the armour itself.

The velcro straps onto the belt and the three loops go around the belt to provide a second set of fasteners.

Glowy & done :)

Tagged with: